Written Estimate First
Nothing is repaired until you approve it
Maytag Washer LF Code: Why It Fills Too Slowly
LF on a Bravos, Bravos XL or other Maytag top-loader means long fill. Most of the time the fix is at the faucets or the drain hose, and this page walks through both.
What LF Means on a Maytag Washer
Maytag uses LF, Lo FL and F8 E1 for the same condition: the washer is taking too long to fill. Maytag’s top-load washers need both hot and cold water flowing to the valve, so one closed faucet is enough to trigger it. A drain hose pushed too deep into the standpipe can also siphon water out as it fills. When the washer senses a supply problem, Maytag says the lid locks and the washer pumps out for 8 minutes, so wait for that to finish. Codes vary by model; your manual has the list for yours. Source: Maytag LF error code (opens in a new tab).
Based in Plano
Serving homes across Dallas–Fort Worth
Real Warranty
90 days, 6 months for members
Diagnostic Credited
Toward the repair if you go ahead
Evenings and Weekends
Open daily, 8–8
What You May Notice With LF
LF usually shows up in one of these ways.
Why a Maytag Washer Shows LF
Maytag lists these causes. The first three are things you can check.
How to Clear LF on a Maytag Washer
Work through Maytag’s checks in this order before booking a visit.
Open both faucets fully
Turn the hot and cold faucets behind the washer all the way open and confirm both inlet hoses are attached and free of kinks. Maytag says both supplies must flow.
Check the drain hose depth
Only about 4.5 inches of drain hose should sit inside the standpipe, held by the U-shaped hose form. Don’t seal the opening with tape. Maytag’s minimum standpipe height is 39 inches.
Clear kinks and clogs
Straighten the drain hose and clear a blocked laundry sink if the washer drains into one, then start a new cycle.
When to Call a Technician
Schedule a repair if:
- LF returns with both faucets open
- Water pressure at the faucets is good
- The drain hose setup is correct
- The washer fills on one side only
More Maytag Washer Help
Maytag washer repairMore help, including other Maytag codes:
Whirlpool F8E1 long fill guideMaytag washer Sud error codeMaytag washer LdL error codeMaytag dryer Check Vent error codeMaytag dishwasher Clean Light error codeAll Maytag appliance repairMaytag top-load HE washer codesWritten estimate first
LF Won’t Go Away?
We test the inlet valve, pressure sensing and controls on Maytag washers and price the repair before any work.
- Diagnostic fee credited toward the repair
- 90-day warranty, 6 months for members
- Open daily, 8 AM–8 PM
Maytag LF Questions
Yes. Maytag groups all three as long fill: the washer is taking too long to fill. Which one you see depends on the display on your model.
Moves often leave a faucet partly closed, kink an inlet hose or push the drain hose too far into the standpipe. Maytag says only about 4.5 inches of hose belongs in the standpipe; deeper than that and it can siphon.
Maytag says when the washer doesn’t sense both supplies, the lid locks and it pumps out for 8 minutes. Let that finish before you open it.
Yes. If both faucets are open, pressure is good and the hose setup is right, a technician checks the inlet valve, its screens and the pressure sensing before replacing anything.
ALAS Appliance Repair
Get Your Maytag Washer Filling Normally
Written Estimate First- Diagnostic Credited
- Real Warranty
- Based in Plano