Business Profile
Maytag Dishwasher Repair at Your Sink
Standing water after the cycle, a Clean light blinking a pattern, or plates coming out with grit on them. We read the Maytag code, test the part behind it and fix your dishwasher in place across Dallas–Fort Worth.
- Price confirmed before repairs
- We read Maytag blink codes
- Pumps, filters, chopper, heating
- Seven days a week
Business Profile
4.8
288 reviews
Schedule Maytag Dishwasher Service
Maytag Dishwasher Repair, Code by Code
Maytag dishwashers are built around what Maytag calls Dual Power Filtration: a microfilter that keeps food out of the spray water, and a stainless chopper that grinds particles small enough to drain. That design is why so many Maytag dishwasher calls trace back to the filter and drain path, and why the chopper is one of the parts Maytag covers for ten years. When something goes wrong, models without a display blink the Clean light in a two-part pattern, which Maytag explains how to read: the first group of flashes is the F number and the second group is the E number. F9 E1 points to a long drain and F8 E4 to water in the base, for example. Your technician reads the code, tests the drain pump, wash motor, heating element, float and controls, and gives you the price before any part is replaced.
Open the door: the Maytag tag is usually on the upper left of the tub frame, or on the underside of the control panel on top-control models. A photo of it and the blink pattern or code you see is the most useful thing you can send.
Most common calls
Maytag Dishwasher Problems and Where to Look
Start here, then try the linked guide. Many of these begin with a few minutes at the filter.
| Symptom | Common causes a technician checks | Guide |
|---|---|---|
| Standing water or F9 E1 | Clogged filter, kinked drain hose, disposer not cleared, a blocked air gap or a drain pump that has stopped. | Maytag blink code guide |
| Clean light blinking | An error code given as flashes. Count the two groups to get the F and E numbers, then check that code. | Maytag blink code guide |
| Sani light flashing | Incoming water below 120°F, the door opened mid-cycle, an interrupted cycle, or a heating or sensing fault. | Maytag Sani light guide |
| Gritty or cloudy dishes | A dirty microfilter, a worn chopper, blocked spray arms, too little detergent, or mineral film from hard water. | Dishwasher repair |
| Water on the floor or F8 E4 | A leak into the base that lifts the float, a door gasket, a loose hose connection or oversudsing from the wrong detergent. | Maytag blink code guide |
| Dishes still wet | Empty rinse aid, PowerDry not selected, a failed heating element, or plastics that naturally hold water. | Dishwasher repair |
| Won’t fill or H20 | The supply valve under the sink is off, a kinked supply hose, a failed inlet valve or a float stuck up. | Maytag blink code guide |
| All lights flashing | Maytag says this means the door opened mid-cycle and the cycle paused. Close it firmly until it latches. | Maytag blink code guide |
Maytag Dishwasher Parts We Repair
Wash, drain, heat and control parts sourced for your Maytag model number.
Drain Pumps
Pumps behind standing water and F9 E1.
Filters and Choppers
The Dual Power Filtration parts that keep water clean.
Wash Motors
Circulation motors behind F7 E2 and weak washing.
Heating Elements and Thermistors
Heat for drying and the Sanitize option.
Inlet Valves and Floats
Fill parts behind H20 and overfilling.
Door Latches and Gaskets
Latches that won’t catch and seals that drip.
Spray Arms and Racks
Arms, wheels and rack parts that wear out.
Controls and Keypads
Boards and panels behind F6 E1 and dead buttons.
Repair or replace
Should You Repair Your Maytag Dishwasher?
Many Maytag dishwasher repairs are a pump, valve, latch or heating element, each a single part. Maytag also lists the stainless tub, nylon racks and chopper under its 10-year limited parts warranty on dishwashers made after 2017, which takes some of the larger repairs off the table. A rusted tub floor or a dishwasher needing a pump and a control together is when a new one is worth pricing.
Usually worth repairing
- The fault is a pump, valve, latch or element
- It was made after 2017 and the tub, racks or chopper failed
- It fits a custom panel or tight cabinet opening
- The tub and door are in good condition
Worth weighing carefully
- The tub floor is rusted or cracked
- It needs a wash motor and control at once
- It is old and has needed several repairs
- The quote is more than half the price of a new one
Comparing new dishwashers? Check water and energy use with ENERGY STAR certified dishwashers
Protect Your Home.
Choose Your Plan.
Preventive maintenance, priority service, and repair savings — all under one membership.
MonthlyAnnual
Silver
Essential Home Care
$49/mo
1HVAC
5Appliances
6moWarranty
- ✓1 HVAC system — spring & fall visits
- ✓Up to 5 major appliances
- ✓1 annual appliance check-up
- ✓15% off all repair labor
- ✓HVAC diagnostic just $69
Gold
Premium Home Care
$79/mo
2HVAC
8Appliances
6moWarranty
- ✓Up to 2 HVAC systems covered
- ✓Up to 8 major appliances
- ✓1 free HVAC diagnostic/year
- ✓20% off all repair labor
- ✓Priority scheduling
Platinum
Elite Home Protection
$129/mo
3HVAC
12Appliances
6moWarranty
- ✓Up to 3 HVAC systems covered
- ✓Up to 12 major appliances
- ✓Twice-yearly appliance maintenance
- ✓30% off all repair labor
- ✓Premium member routing
Leak
Maytag Dishwasher Leaking Under the Cabinet?
Water under a dishwasher can soak the subfloor long before it shows. Stop the cycle, cut the power and close the valve under the sink, then book a visit. After-hours visits are available at an extra charge.
How it works
How a Maytag Dishwasher Visit Works
Book with the code
Count the blinks or note the display code, and send the model tag photo when you book online or call.
Code to cause
The technician confirms the code, then tests the pump, motor, valve, float or heating circuit it points to.
Written price
You see the diagnosis and the price before work starts. If the tub, racks or chopper is a Maytag-covered part, we say so.
Full cycle tested
After the repair we run fill, wash and drain, check for leaks and put the warranty terms on your invoice.
Troubleshooting
Maytag Dishwasher Lights and Codes
Guides built from Maytag’s own help articles.
When a Maytag Dishwasher Needs a Technician
Where we work
Maytag Dishwasher Repair Around DFW
We repair Maytag dishwashers in kitchens in Plano, Frisco, McKinney, Allen, Prosper, Lucas, Parker, Richardson, Dallas, Highland Park, University Park, Coppell, Flower Mound, Southlake, Westlake, Colleyville, Keller, Grapevine, Argyle and Trophy Club. Find your city below or check your ZIP code.
PlanoDishwasher repairFriscoDishwasher repairMcKinneyDishwasher repairAllenDishwasher repairProsperDishwasher repairLucasDishwasher repairParkerDishwasher repairRichardsonDishwasher repairDallasDishwasher repairHighland ParkDishwasher repairUniversity ParkDishwasher repairCoppellDishwasher repairFlower MoundDishwasher repairSouthlakeDishwasher repairWestlakeDishwasher repairColleyvilleDishwasher repairKellerDishwasher repairGrapevineDishwasher repairArgyleDishwasher repairTrophy ClubDishwasher repair
Maytag Dishwasher Questions We Get Asked
Maytag’s F9 E1 steps cover it: take out the filter and rinse it under running water, check the drain hose to the sink for kinks, run the disposer and, on a new install, make sure the disposer knockout plug was removed. If water still stands, the drain pump needs testing.
Count the first set of flashes (the F number), wait through the short pause, then count the second set (the E number). Seven flashes, a pause and one flash is F7 E1. See our blink code guide.
In a Maytag, grit usually means the microfilter needs cleaning or the chopper isn’t grinding particles away. Rinse the filter, check the spray arms turn freely and use enough detergent for your water.
Maytag says the sanitizing temperature wasn’t reached. Run your kitchen tap hot first; Maytag’s minimum is 120°F. See our Sani light guide.
Maytag says to disconnect power for 30 seconds: unplug it, or switch off the breaker on a hard-wired model, then restore power.
Check the rinse aid first, and select PowerDry on models that have it. Plastics hold water more than glass. If everything stays wet, the heating element may have failed.
Mineral film can cloud glasses and build up on the filter and spray arms over time. Rinse aid and regular filter cleaning help.
On dishwashers made after 2017, Maytag’s 10-year limited parts coverage lists the stainless tub, nylon racks and chopper. Pumps, motors and controls are covered in the first year only (Maytag warranty (opens in a new tab)).
Start with Maytag if your dishwasher is in its first year, because Maytag covers all parts and labor that year. After that, Maytag’s 10-year coverage is limited to certain parts (on a dishwasher: the stainless tub, nylon racks and chopper) on products made after 2017, and labor is no longer included (Maytag 10-year limited parts warranty (opens in a new tab)). ALAS is an independent company, not a Maytag service provider. We handle out-of-warranty repairs and repairs owners choose to have done locally, and if a covered Maytag part is the problem, we will tell you so you can claim it.
Unload the dishwasher, clear the cabinet under the sink and write down the blink pattern or code.
Our technicians cover the Dallas–Fort Worth area: Collin County cities like Plano, Allen, McKinney and Frisco, plus Dallas, Richardson, Coppell and the Southlake, Keller and Grapevine side of Tarrant County.